Understanding Plumbing Basics When Installing a Bathtub
Understanding Plumbing Basics When Installing a Bathtub
Blog Article
Presented here below you can discover lots of awesome advice around A Step-by-Step Guide to Installing a Bathtub.
Setting up a bath tub isn't exactly brain surgery, but it does call for solid plumbing, carpentry, and also in some cases, tiling skills. Changing an old bath tub with a new one is also a moderately hard project. If the old tub is readily easily accessible, the task can relocate quickly; if you need to open up a wall to remove the old bathtub and also position the brand-new bathtub, the job is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly need a helper to leave the old bathtub as well as set in the brand-new one. Make sure you have qualified on your own for the work and are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed project, it is much better to think about employing one prior to you start. Chances are you may require a specialist plumber to make tube links.
This write-up will help you set up a brand-new bathtub in your restroom if you have already bought a brand-new bathtub and also don't require to alter the plan of your previous supply of water pipes.
Your devices as well as material list need to make up the following:
Preparing for the Setup
To start with, the supporting frame supplied with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to avoid stress on the bath tub.
Fit the versatile faucet connectors to the bottom of the two taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last setting.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be fairly bothersome due to the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Prior to proceeding to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Using the two wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto four little factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bath tub up until the spirit level reviews level.
To mount faucets, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Turn on the water system and examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and additionally inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's user's manual. Tiling and securing around the bathtub ought to wait up until the bath tub has been used a minimum of once as this will settle it into its final setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the current supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in place between the tap and also the sink. Safeguard the tap in position with the producer provided backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical faucet ports. The previous kind should be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a rigid seal, triggering the water to penetrate the wall between the bath and the tiling, resulting in issues with dampness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub remains in use. The sealer can break fairly early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that content about Tools You Need to Install a New Bathtub while looking around the web. Don't hesitate to take the time to promote this blog posting if you liked it. Thanks a lot for going through it.
Need help? Call. Report this page